Turning Silver and Copper Metals Black: Some Oxidizing Techniques

Warren Feld
10 min readApr 18, 2020

--

OXIDIZING TECHNIQUES
(Use bare wire, if you intend to oxidize it; this means it has no protective lacquer finish on it to prevent it from tarnishing)

Liver of Sulfur solid form

1. USING LIVER OF SULFUR

Step 1 Preferably work outside when using Liver of Sulfur (LOS). Make sure you wear gloves and designate glass or ceramic containers that will be used solely for this purpose.

Step 2 Clean the silver before you begin. Any polishing residues, wax or fingerprints could affect the consistency of the oxidation. Hot soapy water and an old toothbrush work well.

Step 3 Make a neutralizing bath. You will use this later to neutralize the silver once you have finished oxidizing.

Step 4 To make the neutralizing bath: Using one Mason jar, mix two teaspoons of baking soda in one cup of cold water.

Step 5 Stir solution until the baking soda is dissolved. Set aside for later.

Step 6 Prepare your workstation. You need two mason jars with one cup of hot water in the LOS solution, the neutralizing bath you just made, Liver of Sulfur, the silver you wish to oxidize, a pair of gloves, a plastic spoon and some paper towels. (Hot water (not boiling): 30 seconds in microwave) (Use glass jars, not plastic)

In the one with the piece you wish to oxidize, if you use hot water, oxidation will occur very quickly. If you use room temperature or even ice water, the oxidation will take longer to occur. With silver, this will give you an opportunity to control what color tone the final piece will have. But with copper, the metal darkens extremely fast.

Step 7 Drop the silver into the water (hot, room temp or cold) of one Mason jar.

Step 8 In the other Mason jar add 1 pea sized lump of LOS to the hot water.
The hotter the solution, the faster the oxidation. Alternative: Room temperature LOS solution, and put silver in ice-cold water. A greater temperature difference slows patina process, and can get more variation in colors with blues and golds, not just blacks.

Liver of Sulfur gel form

Liver of Sulfur gel can be brushed on using a small paint brush, or you can make a solution. To make a solution, coat half a teaspoon with the gel and allow the excess to drip off. Then dip the spoon in a container of hot water and allow to dissolve.

Step 9 Mix thoroughly.

Step 10 Remove the silver from the water and carefully place the silver into the LOS solution trying not to splash.

Step 11 Leave the silver in the LOS solution until it reaches the desired color, stirring occasionally to get an even finish. [This can happen within seconds, within 5 minutes, within 15 minutes, or within 1 hour, depending on the piece and how dark you want it, and the differences in solution temperatures.]

Step 12 Remove the silver from the LOS solution and place the silver in the neutralizing bath. This will stop any further oxidation of the silver.

Step 13 Remove the silver form the neutralizing bath and dry slightly with the paper towel.

Step 14 You can either tumble the silver to polish and seal the oxidized finish or you can use a polishing cloth. You can try rough paper towels. You can try 0000 steel wool. Be careful not to completely rub off the oxidation.

Step 15 Put two teaspoons of baking soda into the LOS solution to neutralize it.

Step 16 Loosely seal the Mason jar that contains the LOS solution and leave the jar out doors, out of the reach of children or animals. The LOS will degrade and eventually turn clear. Once it is clear it is no longer toxic and you can dispose of it by diluting the solution and flushing it down the drain.

Black Max (liquid)

2. USING BLACK MAX (Contains hydrochloric acid and tellurium)

The result from Black Max is a bit shinier black finish than Liver of Sulphur, which is more matte. With liver of Sulphur, oxidation does not wear off as fast. Can’t get the range of oxidations colors with Black Max, as you can with LOS.

For silver, immerse in or apply Black Max with a cloth or applicator until the desired finish is obtained (20–30 seconds is the norm). Enough solution in jar to cover your piece.

Do not heat solution or piece.

Otherwise, you will follow similar steps as with LOS, including the baking soda solution to neutralize the reaction.

3. USING HARD BOILED EGG (using Sulphur to oxidize silver or copper)

Boil the egg, and peel the shell.
Put the peeled egg inside a zip lock bag.
Use your fingers to crush the peeled egg inside the bag.
Put your piece of silver inside the bag and into the crushed egg pieces.
Check every 15 minutes to see if it is sufficiently oxidized for you. Can easily take 1 hour.
Rinse with warm water and some dish detergent.
Use paper towel or 0000 steel wool to brush off any excess oxidation.

Antiquing Solution

4. ANTIQUING or VARNISH SOLUTION

Another thing you can do is to buy an antiquing solution, or use a dark color varnish.

You paint this on, and then rub it off with a soft cloth. Let it dry for about 20 minutes, and repeat, if you need the antiquing to be darker.

This leaves a glossy black finish. Here, again, you usually want to leave some gradations of color on the metal, so that the top surfaces are shinier than the crevices.

Anything with ammonia in it

5. AMMONIA

If you want to speed up the tarnishing process, but do not want to turn your product black, spray your metal with Windex with Ammonia.

The ammonia will turn the silver black, and the low amount of ammonia in this product will make the process very gradual. With more ammonia concentration, the faster and the blacker it will turn.

6. OTHER CHOICES

You will find online a wide range of patina’s. These typically are in liquid form. Different patinas work with different metals. Different patinas have different final coloration results. You can get ones that do blues or purples or golds or rainbow effects.

Steel Wool

FINISHING YOUR PIECE OFF AFTER YOU OXIDIZE IT

After you have oxidized and patina’d your piece, you probably want to let some of the higher areas get a little shinier again, leaving the recessed areas dark.

Easy to do.

Take some steel wool (#0000) or a rougher paper towel, or a soft bristle toothbrush, and gently rub over the surface. Like an artist, you will control where you want highlights and where you want lowlights.

Think you went to far? Then oxidize again. Not a problem.

Other Articles of Interest by Warren Feld:

Best Way To Thread Your Needle

Bead Stringing With Needle and Thread

Beading Threads vs. Bead Cord

Turning Silver and Copper Metals Black: Some Oxidizing Techniques

Color Blending; A Management Approach

Cleaning Sterling Silver Jewelry: What Works!

What Glue Should I Use When Making Jewelry?

When Choosing Colors Has You Down, Check Out The Magic Of Simultaneity Effects

The Color Effects of Threads

Wax, Wax, Wax

When You Attend A Bead Show…

When Your Cord Doesn’t Come With A Needle…What You Can Do

Duct Tape Your Pliers

What To Know About Gluing Rhinestones

Know Your Anatomy Of A Necklace

How Does The Jewelry Designer Make Asymmetry Work?

I hope you found this article useful. Be sure to click the CLAP HANDS icon at the bottom of this article.

Also, check out my website (www.warrenfeldjewelry.com).

Subscribe to my Learn To Bead blog (https://blog.landofodds.com).

Visit Land of Odds online (https://www.landofodds.com)for all your jewelry making supplies.

Enroll in my jewelry design and business of craft video tutorials online.

Add your name to my email list.

__________________________________

CONQUERING THE CREATIVE MARKETPLACE: Between the Fickleness of Business and the Pursuit of Design

How dreams are made
between the fickleness of business
and the pursuit of jewelry design

This guidebook is a must-have for anyone serious about making money selling jewelry. I focus on straightforward, workable strategies for integrating business practices with the creative design process. These strategies make balancing your creative self with your productive self easier and more fluid.

Based both on the creation and development of my own jewelry design business, as well as teaching countless students over the past 35+ years about business and craft, I address what should be some of your key concerns and uncertainties. I help you plan your road map.

Whether you are a hobbyist or a self-supporting business, success as a jewelry designer involves many things to think about, know and do. I share with you the kinds of things it takes to start your own jewelry business, run it, anticipate risks and rewards, and lead it to a level of success you feel is right for you, including

· Getting Started: Naming business, identifying resources, protecting intellectual property

· Financial Management: basic accounting, break even analysis, understanding risk-reward-return on investment, inventory management

· Product Development: identifying target market, specifying product attributes, developing jewelry line, production, distribution, pricing, launching

· Marketing, Promoting, Branding: competitor analysis, developing message, establishing emotional connections to your products, social media marketing

· Selling: linking product to buyer among many venues, such as store, department store, online, trunk show, home show, trade show, sales reps and showrooms, catalogs, TV shopping, galleries, advertising, cold calling, making the pitch

· Resiliency: building business, professional and psychological resiliency

· Professional Responsibilities: preparing artist statement, portfolio, look book, resume, biographical sketch, profile, FAQ, self-care

548pp.

Kindle, Print, Epub

SO YOU WANT TO BE A JEWELRY DESIGNER
Merging Your Voice With Form

So You Want To Be A Jewelry Designer reinterprets how to apply techniques and modify art theories from the Jewelry Designer’s perspective. To go beyond craft, the jewelry designer needs to become literate in this discipline called Jewelry Design. Literacy means understanding how to answer the question: Why do some pieces of jewelry draw your attention, and others do not? How to develop the authentic, creative self, someone who is fluent, flexible and original. How to gain the necessary design skills and be able to apply them, whether the situation is familiar or not.

588pp, many images and diagrams Ebook , Kindle or Print formats

The Jewelry Journey Podcast
“Building Jewelry That Works: Why Jewelry Design Is Like Architecture”
Podcast, Part 1
Podcast, Part 2

PEARL KNOTTING…Warren’s Way
Easy. Simple. No tools. Anyone Can Do!

I developed a nontraditional technique which does not use tools because I found tools get in the way of tying good and well-positioned knots. I decided to bring two cords through the bead to minimize any negative effects resulting from the pearl rotating around the cord. I only have you glue one knot in the piece. I use a simple overhand knot which is easily centered. I developed a rule for choosing the thickness of your bead cord. I lay out different steps for starting and ending a piece, based on how you want to attach the piece to your clasp assembly.

184pp, many images and diagrams Ebook, Kindle or Print

SO YOU WANT TO DO CRAFT SHOWS:16 Lessons I Learned Doing Craft Shows

In this book, I discuss 16 lessons I learned, Including How To (1) Find, Evaluate and Select Craft Shows Right for You, (2) Determine a Set of Realistic Goals, (3) Compute a Simple Break-Even Analysis, (4) Develop Your Applications and Apply in the Smartest Ways, (5) Understand How Much Inventory to Bring, (6) Set Up and Present Both Yourself and Your Wares, (7) Best Promote and Operate Your Craft Show Business before, during and after the show.

198pp, many images and diagrams, Ebook, Kindle or Print

BASICS OF BEAD STRINGING AND ATTACHING CLASPS

Learning Bead Stringing Is More Than
Putting Beads On A String And Tying On A Clasp

There is an art and skill to stringing beads. First, of course, is the selection of beads for a design, and the selection of the appropriate stringing material. Then is the selection of a clasp or closure, appropriate to the design and use of the piece.

You want your pieces to be appealing. You want them to wear well. You want someone to wear them or buy them. This means understanding the basic techniques, not only in terms of craft and art, but also with considerations about architecture, mechanics, and some sociology, anthropology and psychology.

In this book, I go into depth about: (1) Choosing stringing materials, and the pros and cons of each type, (2) Choosing clasps, and the pros and cons of different clasps, (3) All about the different jewelry findings and how you use them, (4) Architectural considerations and how to build these into your pieces, (5) How better designers use cable wires and crimp, as well as, use needle and thread to string beads, (6) How best to make stretchy bracelets, (7) How to make adjustable slip knots, coiled wire loops, and silk wraps, (8) How to finish off the ends of thicker cords or ropes, so that you can attach a clasp, (9) How to construct such projects as eyeglass leashes, mask chains, lariats, multi-strand pieces, twist multi-strand pieces, and memory wire bracelets, (10) How different teaching paradigms — craft vs. art vs. design — might influence the types of choices you make.

452 pp, many images, illustrations, diagrams, Ebook, Kindle or Print

___________________________________________

Your membership fee directly supports Warren Feld and other writers you read. You’ll also get full access to every story on Medium. CLICK To Find Out More.

--

--

Warren Feld
Warren Feld

Written by Warren Feld

Beading and jewelry making have been wonderful adventures, from custom work, production work, and teaching. *Design is about the ability to make smart choices.